收藏本站
BR24T □□□□ Series
Technical Note
● WP valid timing (write cancel)
WP is usually fixed to 'H' or 'L', but when WP is used to cancel write cycle and so forth, pay attention to the following WP
valid timing. During write cycle execution, in cancel valid area, by setting WP='H', write cycle can be cancelled. In both byte
write cycle and page write cycle, the area from the first start condition of command to the rise of clock to taken in D0 of
data(in page write cycle, the first byte data) is cancel invalid area.
WP input in this area becomes Don't care. The area from the rise of SCL to take in D0 to input the stop condition is cancel
valid area. And, after execution of forced end by WP, standby status gets in.
? Rise of D0 taken clock
SCL
SCL
? Rise of SDA
SDA
D1
D0
ACK
SDA
D0
ACK
Enlarged view
Enlarged view
K address
SDA
S
T Slave
A
R address
T
A
C Word
L
A
C D7 D6 D5 D4 D3 D2 D1 D0
K
L
A
C
K
L
Data
A
C
K
L
S
T
O
P
tWR
WP cancel invalid area
WP cancel valid area
WP cancel invalid area
WP
Data is not written.
Fig.50 WP valid timing
● Command cancel by start condition and stop condition
During command input, by continuously inputting start condition and stop condition, command can be cancelled. (Fig.51)
However, in ACK output area and during data read, SDA bus may output 'L', and in this case, start condition and stop
condition cannot be input, so reset is not available. Therefore, execute software reset. And when command is cancelled by
start, stop condition, during random read cycle, sequential read cycle, or current read cycle, internal setting address is not
determined, therefore, it is not possible to carry out current read cycle in succession. When to carry out read cycle in
succession, carry out random read cycle.
SCL
SDA
1
0
1
0
Start condition
Stop condition
Fig.51 Case of cancel by start, stop condition during slave address input
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
13/21
2011.03 - Rev.A
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
BR25L640F-WE2 IC EEPROM SER 64KB SPI BUS 8SOP
BR25S128GUZ-WE2 IC EEPROM SPI 128KB 12-WLCSP
BR25S256F-WE2 IC EEPROM SPI 256KB 20MHZ 8-SOP
BR34E02FVT-WE2 IC EEPROM SPD 2KB I2C 8TSSOP
BR34L02FV-WE2 IC EEPROM 2KBIT 400KHZ 8SSOP
BR93L76RFVJ-WE2 IC EEPROM 8KBIT 2MHZ 8TSSOP
BS08D-112 TRIGGER BILTRL SW 175MA TO-92
BU04P-TZ-S TZ CONN 4 POS SINGLE ROW
相关代理商/技术参数
BR24T256FVWGE2 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BR24T256FVWGTR 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BR24T256F-WE2 功能描述:电可擦除可编程只读存储器 Hi-Rel Serial 电可擦除可编程只读存储器 of I2C BUS RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
BR24T256FWGE2 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BR24T256FWGTR 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BR24T256NUXWGE2 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BR24T256NUXWGTR 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BR24T256-W 制造商:ROHM Semiconductor 功能描述: